Нужна твоя консультация.Плату помен

Нужна твоя консультация.
Плату поменяли, процедуру с ключами выполнили.
Печатная станция (print station) запустилась и соединилась с контроллером (system controller CS410).
Но присутствуют три ошибки.

1. В окне «Ink Concentration» ошибка «State Table Error». Foto 1.
В закладке «Diagnostic» в окне «State Table Entry» при смене шагов в таблице не происходит никаких изменений, то есть таблица пуста. Foto 2.

2. В окне «Ink Concentration» ошибка «Inkdex File Error». Foto 3.
При этом в окне «Print Station Setting» для выбора присутствует только один номер чернил 6091036. Эти чернила используем в DT90. В станции DT91 необходимы чернила 6091500. Foto 4.

3. В окне «Ink/Amb°C» ошибка «Umbilical Heater Control Error». Нагрев Umbilical не происходит. Foto 1.

Что мы можем сделать?

Результаты (английский) 1:

Need your advice.Cost was a key procedure performed.Print station (print station) started and connected to the controller (system controller CS410).But there are three errors. 1. in the window "Ink error" Concentration "State Table" Error ". Foto 1.In the Diagnostic tab in the State Table Entry when changing the steps in table no changes occur, that is, the table is empty. Foto 2.2. in the window "Ink error" Inkdex "Authors" File Error ". Foto 3.In the Print Setting to select the Station, there is only one ink 6091036. These inks we use DT90. The station DT91 6091500 inks are required. Foto 4.3. in the window "Ink/Amb° c" error "Umbilical Control Heater Error". Heating of the Umbilical is not happening. Foto 1. What can we do?

Результаты (английский) 2:

Need your advice.
Pay system, the procedure carried out with the keys.
Print Station (print station) launches and connects to the controller (system controller CS410).
But there are three errors. 1. In the «Ink Concentration» error «State Table Error». Foto 1. In the tab «Diagnostic» in the «State Table Entry» when changing steps in the table there is no change, that is, the table is empty. Foto 2. 2. In the «Ink Concentration» error «Inkdex File Error». Foto 3. In the window «Print Station Setting» for selection there is only one number 6091036. ink These inks use in DT90. The station DT91 necessary ink 6091500. Foto 4. 3. In the «Ink / Amb ° C» error «Umbilical Heater Control Error». Umbilical heating does not occur. Foto 1. What can we do?

Результаты (английский) 3:

Need your advice.
the Card changed, the procedure for the keys have fulfilled.
the printing station (print station) starts and is seated with the controller (system controller CS410) .
but there are three errors.

1.In the window "Ink concentration" error "state table error". Criticism 1.
in the tab "Diagnostic" in the window "state table entry" when changing steps in the table does not make any changes, then there is also a table is empty. Criticism 2.lord 2. In the window "Ink concentration" error "Inkdex file error". Criticism 3.
With this in the window "Print Station Setting" to select is present only one ink number 6091036. These inks use in DT90. The station DT91 are required ink 6091500. Criticism 4.lord 3. In the window "ink/Amb°C" error "Umbiliсаl Heater Control Error".Heat Umbiliсаl does not occur. Criticism 1.

what can we do?