Основной принцип работы данного обо

Основной принцип работы данного оборудования основан на термометрическом методе – замера температуры при твердении (схватывании)бетона - энергии гидратации.
Для этого в сваи заранее на всю длину закладывают металлические трубки определенного диаметра для перемещения в них термозонда с инфракрасными датчиками. Количество трубок зависит от диаметра сваи.
Глубинный датчик, соединенный с прибором TIP, отслеживает положение зонда во время опускания его на полную длину каждой трубки. Данные по температурам и глубинам, как правило, собираются через 12-48 часов после бетонирования в зависимости от состава бетонной смеси и диаметра скважины.
Специалистами компании PDI PileDynamicsInc. эмпирическим путем выведена зависимость диаметра сваи от температуры бетона, вариантов добавок, и времени измерения.что регламентируется стандартом ASTM D7949. Т.е. чем больше количество бетона, тем выше выделяемая бетоном температура (энергия гидратации) соответственно больше диаметр сваи. Совокупность замеров по длине сваи формирует график зависимости температуры от диаметра сваи.
Измерения в полевых условиях позволяют в режиме реального времени увидеть предварительный график (профиль) кривой температуры, характеризующий общую форму скважины. На этом уровне данные полученные при замерахв одной или нескольких трубках, а также в определенные периоды времени собираются для дальнейшего анализа обученными специалистами с использования специального программного обеспечения.
Программное обеспечение, разработанное компанией PDI PileDynamicsInc. позволяет получить точную двухмерную и трехмерную модель исследуемой сваи.

Результаты (английский) 1:

The basic principle of this equipment is based on the termometričeskom method-measuring the temperature at tverdenii (catching) concrete energy of hydration. To do this, in piles in advance on the entire length of the lay a specific diameter metal tubes to move them termozonda with infra-red sensors. Number of pipes depends on the diameter of the pile. Depth sensor, coupled with the instrument TIP, tracks the position of the probe during the lowering of the full length of each tube. Data on temperatures and depths, usually going through the 12-48 hours after concreting depending on the composition of the concrete mix and the diameter of the borehole. Specialists of the company PDI PileDynamicsInc. empirically derived dependence diameter piles of concrete, temperature variations and measuring time. that is governed by ASTM D7949. I.e. the more concrete, the higher the allocated concrete temperature (energy of hydration) respectively, more diameter piles. The combination of measurements along the length of the piles generates a dependency graph of temperature from the diameter of the pile. Measurements in the field provide real-time see tentative schedule (profile) temperature curve describing the General form of the wells. At this level, the data obtained from the zamerahv one or more tubes, as well as during certain periods of time are collected for further analysis by trained specialists with the use of special software. Software developed by PDI PileDynamicsInc. allows you to obtain accurate 2D and 3D model researched piles.

Результаты (английский) 2:

The basic principle of this equipment is based on the method of Thermometer - temperature measurement hardening (grasp) of concrete -. Hydration energy
To do this in advance of the pile lay the entire length of metal pipe of a certain diameter to move them in the thermal probe with infrared sensors. The number of tubes depends on the diameter of the pile.
Depth sensor connected to the device TIP, tracks the position of the probe during its lowering to the full length of each tube. Data on temperature depth and usually going through 12-48 hours after concreting depending on the composition of the concrete mix and the borehole diameter.
Specialists Company PDI PileDynamicsInc. empirically derived relationship of the diameter of the pile concrete temperature, addition of options and time izmereniya.chto governed by ASTM D7949 standard. Those. the greater the amount of concrete above the temperature allocated concrete (hydration energy) is correspondingly greater diameter of the pile. The set of measurements on the pile length generates a graph of temperature of the pile diameter.
Measurements in the field in real-time to see the preliminary schedule (profile) of the temperature curve, characterizing the overall shape of the well operation. At this level, the data obtained by zamerahv one or more tubes, as well as in certain periods of time are collected for further analysis by trained personnel using special software.
The software, developed by PDI PileDynamicsInc. It allows you to get an accurate two-dimensional and three-dimensional model of the test piles.

Результаты (английский) 3:

the main working principle of this equipment is based on the термометрическом method is measuring the temperature in the твердении (схватывании) concrete hydration energy.for this, advance the whole length of a pile in a certain diameter metal tube for displacement in термозонда with infrared sensors. the number of tubes depends on the diameter of pile.a sensor connected to the device for tracking the position of the probe tip, while lowering it on the full length of each tube. the data on temperatures and depths are generally collected from 12 to 48 hours after brought depending on the composition of concrete mixture and the diameter of the bore.the company PDI PileDynamicsInc. an empirical way eastward from the temperature dependence of the diameter of pile concrete, options, additives, and time измерения.что is governed by the standard astm D7949. i.e. the more the number of the concrete, the higher temperature is used in concrete (the energy of hydration), respectively, more than the diameter of the pile. the measurements of the temperature dependence of the diameter of the pile forming pile.measurements in field conditions allow, in real time, to the tentative timetable for the profile curve of the temperature, of the general form of the well. at this level the data obtained in замерахв one or several tubes, as well as in certain periods of time are collected for further analysis by trained technicians using special software.software developed by the company PDI PileDynamicsInc. allows to get accurate two-dimensional and three-dimensional model at the pile.