Линейная скорость заготовки не боле

Линейная скорость заготовки не более 10 метров в минуту
Диаметр заготовки (0,18-2,0) мм
Минимальный диаметр изделия 0,25 мм
Максимальный диаметр изделия 3,0 мм
количество обмоточных систем 2
направление вращения обмоточной системы реверсивное
максимальное число оборотов обмоточной системы 920 оборотов в минуту
Число оборотов обмотчика в "заправочном" режиме (25-30) оборотов в минуту
Время разгона до установленнй скорости не более 10 секунд
Время экстренного торможения машины не более 3 секунд
способ изменения числа оборотов обмоточнй системы плавный
шаг обмотки (0,7-20) мм
Дискретность установки шага обмотки, не более 0,1 мм
способ изменения линейной скорости плавный
ширина используемой ленты (3-12) мм
толщина ленты (10-70) микрометров
диаметр ленты 200 мм
диаметр кольца ленты 75 мм
натяжение ленты от 30 до 250 грамм
стабильность натяжения ленты не более 5%
wrapping должны быть снабжены бесконтактной системой контроля обрыва ленты и системой аварийной остановки машины при обрыве ленты
при refill и отключении машины натяжение заготовки и лент сохраняется

Результаты (английский) 1:

The linear velocity of the workpiece is not more than 10 meters per minuteWorkpiece diameter (0.18 -2.0) mmMinimum diameter 0.25 mmMaximum product diameter 3.0 mmthe number of winding systems 2the direction of rotation of the coil winding system reversethe maximum rotational speed of the winding system 920 revolutions per minuteNumber of revolutions of the wrapper in the "filling" mode (25-30) revolutions per minuteAcceleration up to ustanovlennj speed of no more than 10 secondsEmergency braking time machine no more than 3 secondsHow to change the speed of the obmotočnj system of smoothstep winding (0.7 -20) mmSetup resolution step winding, no more than 0.1 mmHow to change the linear speed of a smooththe width of the Ribbon (3-12) mmtape thickness (10-70) micrometersdiameter 200 mm Ribbonring diameter tape 75 mmthe tension of the tape from 30 to 250 gramsthe stability of the belt tension is not more than 5%wrapping must be equipped with non-contact control system of belt breakage and system of an emergency stop of the machine when the Ribbon is brokenWhen you refill the machine and disconnecting the tension of the tape is blank and

Результаты (английский) 2:

The linear velocity of the workpiece is not more than 10 meters per minute
diameter workpiece (0,18-2,0) mm
minimum diameter of 0.25 mm Product
maximum diameter of 3.0 mm product
number of winding systems 2
the direction of rotation of the winding system reverse
the maximum number of turns of the winding system 920 rpm
The number of revolutions in the winding technician "refueling" mode (25-30) rpm
Acceleration time to set speed no more than 10 seconds
time of emergency braking the car no more than 3 seconds,
a method of changing the speed of a smooth winding
pitch winding (0.7 20) mm
Resolution installation steps winding, not more than 0.1 mm
method of changing the linear velocity of smooth
width tape used (3-12) mm
tape thickness (10-70) micrometers
diameter tape 200 mm
ring diameter of 75 mm tape
belt tension from 30 to 250 grams
stability belt tension of not more than 5%
Wrapping must be equipped with a contactless system failure monitoring tape and emergency stop the machine when the tape is broken
when the machine is turned off and refill the tension of the workpiece and the tapes saved

Результаты (английский) 3:

Linear velocity the workpiece is not more than 10 meters per minute
diameter workpiece (0.18 -2,0) mm
a minimum diameter product 0.25 mm
maximum diameter 3.0 mm product number than systems
2
The direction of rotation system gost yo
maximum number of turns system gost 920 revolutions per minute
обмотчика number of turns in the "charge" mode (25-30) revolutions per minute
Acceleration time to установленни speed not more than 10 seconds
the emergency brake the vehicle not more than 3 seconds
a way to change the number of turns обмоточни system smooth
step coil (0.7 - 20) mm
Power Supply installation step the coil, not more than 0.1 mm
way to change linear speed smooth
width to be used belt (3-12) mm
tape thickness (10-70) micrometers
diameter tape 200 mm
diameter ring tape 75 mm
The tension of the belt 30 to 250 grams
stability belt tension is not more than 5 %
wrapping should be equipped with hands-free control system continuity belt system and emergency stop the machine in the event of an open tape
When refill and machine is turned off and the workpiece tension belts still more multitasking performance