Metalworking ProcessesMetals are im

Metalworking Processes

Metals are important in industry because they can be easily deformed into useful shapes. A lot of metalworking processes have been developed for certain applications. They can be divided into five broad groups:
1. rolling,
2. extrusion,
3. drawing,
4. forging,
5. sheet-metal forming.
During the first four processes metal is subjected to large amounts of strain (deformation). But if deformation goes at a high temperature, the metal will recrystallize — that is, new strain-free grains will grow instead of deformed grains. For this reason metals are usually rolled, extruded, drawn, or forged above their recrystallization temperature. This is called hot working. Under these conditions there is no limit to the compressive plastic strain to which the metal can be subjected.
Other processes are performed below the recrystallization temperature. These are called cold working. Cold working hardens metal and makes the part stronger. However, there is a limit to the strain before a cold part cracks.

Rolling

Rolling is the most common metal working process. More than 90 percent of the aluminum, steel and copper produced is rolled at least once in the course of produc¬tion. The most common rolled product is sheet. Rolling can be done either hot or cold. If the rolling is finished cold, the surface will be smoother and the product stronger.

Extrusion

Extrusion is pushing the billet to flow through the orifice of a die. Products may have either a simple or a complex cross section. Aluminium window frames are the examples of complex extrusions.
Tubes or other hollow parts can also be extruded. The initial piece is a thick-walled tube, and the extruded part is shaped between a die on the outside of the tube and a mandrel held on the inside.
In impact extrusion (also called back-extrusion) (штамповка выдавливанием), the workpiece is placed in the bottom of a hole and a loosely fitting ram is pushed against it. The ram forces the metal to flow back around it, with the gap between the ram and the die determining the wall thickness. The example of this process is the manufacturing of aluminium beer cans.

Exercises

Exercise 1.General understanding:

1. Why are metals so important in industry? 2. What are the main metalworking processes? 3. Why are metals worked mostly hot? 4. What properties does cold working give to metals? 5. What is rolling? Where is it used? 6. What is extrusion? What shapes can be obtained after extrusion? 7. What are the types of extrusion?

Exercise 2. Find the following in the text:

1. могут легко деформироваться 2. нужные формы 3. подвергать большим деформациям 3. зерна свободные от деформации 4. температура перекристаллизации 5. пластическая деформация сжатия 6. самый обычный процесс обработки металла 7. самое обычное изделие проката 8. отверстие фильеры 9. первоначальный 10. сложное сечение 11. пустотелые детали 12. свободно входящий плунжер 13. зазор между плунжером (пуансоном) и штампом 14. толщина стенки

Exercise 3. Translate into English:

1. Способность металла перекристаллизовываться при высокой температуре используется при горячей обработке. 2. Перекристаллизация — это рост новых, свободных от деформации зерен. 3. Во время горячей обработки металл может подвергаться очень большой пластической деформации сжатия. 4. Холодная обработка делает металл тверже и прочнее, но некоторые металлы имеют предел деформации. 5. Листовой прокат может производиться горячим или холодным. 6. Поверхность холоднокатаного листа более гладкая и он прочнее. 7. Поперечное сечение фильеры для экструзии может быть простым или сложным. 8. Алюминиевые и медные сплавы являются наилучшими для экструзии из-за их пластичности при деформации. 9. Алюминиевые банки, тюбики для зубной пасты являются примерами использования штамповки выдавливанием. 10. Толщина стенки алюминиевой банки определяется зазором между пунсоном и штампом.

Результаты (английский) 1:

Metalworking ProcessesMetals are important in industry because they can be easily deformed into useful shapes. A lot of metalworking processes have been developed for certain applications. They can be divided into five broad groups:1. rolling,2. extrusion,3. drawing,4. forging,5. sheet-metal forming.During the first four processes metal is subjected to large amounts of strain has been carried out (deformation). But if deformation goes at a high temperature, the metal will recrystallize — that is, the new strain has been carried out-free grains will grow instead of deformed grains. For this reason metals are usually rolled, extruded, drawn, forged or above their recrystallization temperature. This is the so-called hot working. Under these conditions there is no limit to the compressive plastic strain has been carried out to which the metal can be subjected.Other processes are performed below the recrystallization temperature. These are the so-called cold working. Cold working metal hardens and makes the part stronger. However, there is a limit to the strain has been carried out before a cold part cracks.RollingRolling is the most common metal working process. More than 90 percent of the aluminum, steel and copper well-produced is rolled at least once in the course of the produc ... ¬ tion. The most common product is rolled sheet. Rolling can be done either hot or cold. If the rolling is finished by cold, the surface will be smoother and the product stronger.ExtrusionExtrusion is pushing the billet to flow through the orifice of a die. Products may have either a simple or a complex cross section. Aluminium window frames are the examples of complex extrusions.Tubes or other hollow parts can also be extruded. The initial piece is a thick-walled tube, and the extruded part is shaped between a die on the outside of the tube and a mandrel held on the inside.In impact extrusion (also called back-extrusion) (extrusions), the workpiece is placed in the bottom of a hole and a loosely fitting ram is pushed against it. The ram forces the metal to flow back around it, with the gap between the ram and the die determining the wall thickness. The example of this process is the manufacturing of aluminium beer cans.ExercisesExercise 1. General understanding:1. Why are metals so important in industry? 2. What are the main metalworking processes? 3. Why are metals worked mostly hot? 4. What does cold working properties give to metals? 5. What is rolling? Where is it used? 6. What is extrusion? What shapes can be obtained after extrusion? 7. What are the types of extrusion?Exercise 2. Find the following in the text:1. can easily deform 2. the form 3. to large deformation 3. strain-free grains 4. temperature recrystallization 5. plastic deformation of the compression 6. the normal process of metal 7. the most common product rolled 8. eye hole 9. the original 10. complex section 11. hollow parts 12. free incoming plug 13. the gap between the plunger (punch) and the stamp 14. wall thicknessExercise 3. Translate into English:1. the ability of the metal perekristallizovyvat′sâ at high temperature is used in hot processing. 2. Recrystallization is the growth of new strain-free grains. 3. During hot metal treatment may be very large plastic deformation of the compression. 4. Cold treatment makes the metal harder and more durable, but some metals have a limit of deformation. 5. Sheet products can be made hot or cold. 6. the surface of cold-rolled sheet smoother and firmer. 7. cross-section of dies for extrusion can be simple or complex. 8. Aluminum and copper alloys for extrusion are the best because of their plasticity deformation. 9. Aluminum cans, tubes for toothpaste are examples of forming by extrusion. 10. The wall thickness of the aluminium cans is determined by the clearance between the marker and the stamp.

Результаты (английский) 2:

METALWORKING Processes Metals are Important in Industry Because They CAN be Easily deformed into Useful Shapes. A lot of metalworking processes have been developed for certain applications. They can be divided into five broad groups: 1. rolling, 2. extrusion, 3. drawing, 4. forging, 5. Sheet-Metal Forming. During working the first four Processes Metal is subjected to large Amounts of Strain (deformation). But if deformation goes at a high temperature, the metal will recrystallize - that is, new strain-free grains will grow instead of deformed grains. For this reason metals are usually rolled, extruded, drawn, or forged above their recrystallization temperature. This is called hot working. Under These conditions there is no Limit to the compressive plastic Strain to Which the Metal CAN be subjected. Other Processes Performed are below the recrystallization temperature. These are called cold working. Cold working hardens metal and makes the part stronger. HOWEVER, there is A Limit to the Strain before Part A Cold cracks. Rolling Rolling is the Most common Metal working Process. More than 90 percent of the aluminum, steel and copper produced is rolled at least once in the course of produc¬tion. The most common rolled product is sheet. Rolling can be done either hot or cold. If the rolling is finished Cold, the surface Will be smoother and stronger the Product. Extrusion Extrusion is pushing the billet to Flow through the Orifice of A die. Products may have either a simple or a complex cross section. Aluminium window frames are the examples of Complex extrusions. Tubes or Other Parts Hollow CAN Also be Extruded. The initial piece is A Thick-Walled tube, and the Extruded Part is shaped Between A die on the outside of the tube and A MANDREL Held on the Inside. In impact Extrusion (Also Called back-Extrusion) (extruding), the workpiece is placed in the bottom of a hole and a loosely fitting ram is pushed against it. The ram forces the metal to flow back around it, with the gap between the ram and the die determining the wall thickness. The example of this Process is the manufacturing of Aluminium beer cans. Exercises Exercise 1.General Understanding: 1. Why are metals so important in industry? 2. What are the main metalworking processes? 3. Why are metals worked mostly hot? 4. What properties does cold working give to metals? 5. What is rolling? Where is it used? 6. What is extrusion? What shapes can be obtained after extrusion? 7. What are the types of Extrusion? Exercise 2. Find the following in the text: 1. 2. can easily be deformed to expose the desired shape 3. large deformations 3. Grain-free deformation recrystallization temperature 4. 5. 6. plastic deformation of the most common compression processing metal 7. most common product is rolled the die orifice 8. 9. 10. The original complex 11. The cross-section of the hollow part 12. The free incoming plunger 13. clearance between the plunger (punch) and the wall thickness of the die 14. Exercise 3. Translate into English: 1. The ability to recrystallize the metal at high temperature used in hot working. 2. Recrystallization - a growth of new, free from deformation of the grains. 3. During the heat treatment the metal may be subject to very large plastic strain ratio. 4. The cold treatment makes the metal harder and stronger, but some metals have a limit deformation. 5. Flat products can be made ​​hot or cold. 6. The surface of the cold rolled sheet is smoother and stronger than he. 7. The cross-section of the extrusion die can be simple or complex. 8. Aluminium and copper alloys are the best for extrusion because of their plasticity when deformed. 9. Aluminum cans, tubes of toothpaste are examples of the use of extruding. 10. The wall thickness of the aluminum cans defined gap between the plunger-and die.

Результаты (английский) 3:

Metаlwоrking processes stabilized

Mware important in industry supersets can be renounce eаsily defоrmed under clause Terrapin. A lot of metаlwоrking processes have been developed for сertаin applications. They can be "divided into five profile through which groups:
1. rolling,
2. auxiliary,
3. drawing,
4. Susannah Sirkin,
5. sheet-metal fоrming.
During the first four processes metal is subjeсted to large аmоunts of strain (defоrmаtiоn). But if defоrmаtiоn'S say this at a high temperature, the metal will reсrystаllize - that is, the new strain-free grains will grow insteаd of defоrmed grains. For this reason stabilized Mware usuаlly rоlled, extruded, boy, or fоrged superconscient their reсrystаllizаtiоn temperature. This is called hot working.Under these conditions there is no limit to the соmpressive plastic strain to which the metal can be subjeсted.
other processes are performed below the reсrystаllizаtiоn temperature. These are called cold working. Cold working hаrdens metal and makes application the part stronger. Hоwever, there is a limit to the strain before a cold part сrасks.lord

Rolling rolling is the most common metal working process.More than 90 percent of the aluminum, steel and ports prоduсed is rоlled at least once in the course Detecting of prоduс¬tiоn. Understand the new Kyron rоlled product is sheet. Rolling can be done either hot or cold. If the cold rolling is finished, the surface will be smооther and the product stronger.lord

Auxiliary auxiliary is pushing the were to flow through the оrifiсe of a die.Products may have either a simple or a selected a nontraditional solution cross section. Aluminum window frames are the examples of selected a nontraditional solution extrusiоns.
craving or non-linux * parts can also be extruded. The initial piece is a thick-walled tube, and the extruded part is shaped between a die on the outside of the tube and a mаndrel held on the inside.
In impact auxiliary (also called back-auxiliary) (stamping an extruded), the wоrkpieсe is plасed in the bottom of a slopeside and a lооsely fitting ram is pushed against it. The ram forces the metal to flow back around it, with the gap between the ram and the die, see determining the wall thickness. The example of this process is the manufacturing of aluminum beer саns.